Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 10, 2010 23:34:25 GMT -5
I have tried numerous times, even had my girlfriend and best friend try it. I can't get the UMC-1 to tell me what FM I'm running. I have a metal remote. Also since the only way to get my UMC-1 upgraded is to send it in, would it be worth it to have it upgraded if i haven't had any errors or problems with my current FM? Would there be any improvements with the newest FM??? Thanks in advance  |
|
|
|
Post by Nemesis.ie on Dec 11, 2010 17:04:12 GMT -5
It's "FW" <G> and pressing the key sequence (one after the other) should work - you do have your VFD at some level above off right? |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 11, 2010 17:34:57 GMT -5
It's "FW" <G> and pressing the key sequence (one after the other) should work - you do have your VFD at some level above off right? I just say that. I knew it was FW, brain fart . But i figure it out thanks ;D |
|
|
|
Post by Nemesis.ie on Dec 11, 2010 17:37:56 GMT -5
Good stuff. |
|
|
|
Post by zstokes on Dec 28, 2010 0:08:08 GMT -5
Got my UMC-1 today, and it came with W7.02.00.05.
Sounds good so far. I'm thinking the UPA-5 will open up with some hours on it.
Until my new HDMI TV arrives late this week, I'm still using my Sony KV-40XBR700 (glass, 1080i, 326 pounds) so that means component in + optical in from DishTV receiver, and component out for the display. Does anyone know if the lag when changing channels or inputs goes away with HDMI or at least diminishes itself? Takes between 3 and 4 full seconds for signal acquisition with this setup.
Thanks!
|
|
sz
Minor Hero
Posts: 54
|
Post by sz on May 5, 2011 12:34:41 GMT -5
I just got my UMC-1 couple days ago and my FW is 07.04 blah blah, and I confirmed that this is the latest FW for the time being.
|
|
|
|
Post by kingnordi on May 5, 2011 12:40:00 GMT -5
Thanks for the Information! |
|
|
|
Post by seacoaster on Jun 15, 2011 8:41:04 GMT -5
New UMC-1 owner and forum member here. "Hello" to all.
I just received the unit a few days ago and would like to check the FW version. As with some of the other posters, the key sequence from the remote (aluminum) doesn't work for me. I also checked out the update instruction video but it didn't indicate that there's a screen with the current FW.
Is there a way to check FW version without using the remote (and short of emailing Emo support)?
Thank you.
|
|
LCSeminole
Global Moderator 
Res firma mitescere nescit.
Posts: 20,860
Member is Online
|
Post by LCSeminole on Jun 15, 2011 20:46:35 GMT -5
No other way that I'm aware other than the remote. Just press "mute" then "status" and "vol +". Don't hold them down, just press each in succession and the firmware version will show up on the front panel.
|
|
|
|
Post by marcuslaw on Aug 22, 2011 20:20:48 GMT -5
New UMC-1 owner and forum member here. "Hello" to all. I just received the unit a few days ago and would like to check the FW version. As with some of the other posters, the key sequence from the remote (aluminum) doesn't work for me. I also checked out the update instruction video but it didn't indicate that there's a screen with the current FW. Is there a way to check FW version without using the remote (and short of emailing Emo support)? Thank you. +1 Just go my UMC-1 today and the remote key sequence "mute", "status", then "vol +" does not bring up the firmware #. |
|
|
|
Post by marcuslaw on Sept 2, 2011 4:48:30 GMT -5
New UMC-1 owner and forum member here. "Hello" to all. I just received the unit a few days ago and would like to check the FW version. As with some of the other posters, the key sequence from the remote (aluminum) doesn't work for me. I also checked out the update instruction video but it didn't indicate that there's a screen with the current FW. Is there a way to check FW version without using the remote (and short of emailing Emo support)? Thank you. +1 Just go my UMC-1 today and the remote key sequence "mute", "status", then "vol +" does not bring up the firmware #. While its unboxed and receiving power, I have not gone through the set-up. Could this be why I'm not able to verify the firmware edition? |
|
poggy
Minor Hero
Posts: 11
|
Post by poggy on Sept 14, 2011 21:06:44 GMT -5
Hitting those 3 keys has no effect on my UMC-1.
Suddenly, my UMC-1 audio goes silent when I pause or skip my DVR. This is extremely annoying. Can someone explain how to fix this problem?
thanks, john
|
|
|
|
Post by doc1963 on Sept 14, 2011 21:15:08 GMT -5
Hitting those 3 keys has no effect on my UMC-1. Suddenly, my UMC-1 audio goes silent when I pause or skip my DVR. This is extremely annoying. Can someone explain how to fix this problem? thanks, john This is a well known issue with the UMC-1 and virtually all DVRs. With any luck, the next firmware update (due at any time now) will fix this issue. Other than waiting, you might try avoiding an HDMI connection from your DVR and connecting it to the UMC-1 via component video (which fully supports the max resolution of hi-def via cable... 1080i) and a coax or optical digital connection for audio. Hope this helps... |
|
|
|
Post by alhull on Sept 16, 2011 13:38:44 GMT -5
Hitting those 3 keys has no effect on my UMC-1. Suddenly, my UMC-1 audio goes silent when I pause or skip my DVR. This is extremely annoying. Can someone explain how to fix this problem? thanks, john This is a well known issue with the UMC-1 and virtually all DVRs. With any luck, the next firmware update (due at any time now) will fix this issue. Other than waiting, you might try avoiding an HDMI connection from your DVR and connecting it to the UMC-1 via component video (which fully supports the max resolution of hi-def via cable... 1080i) and a coax or optical digital connection for audio.Hope this helps... and we all know that with the newest generation of audio/video gear, even that component connection will no longer pass 1080i. it will be forced back down to 480. No HD stream on anything except HDMI will be allowed. Thanks, Hollywood. you suck!. |
|
poggy
Minor Hero
Posts: 11
|
Post by poggy on Sept 16, 2011 19:44:45 GMT -5
KEY #1: MUTE KEY #2: STATUS KEY #3: VOL + (Volume Up) With the milled aluminum remote, this sequence does not work on my UMC-1. Works with the little plastic remote. The Vol + key press on the aluminum remote is the culprit because the sequence will also work if I use the aluminum remote for the first two key presses (mute and status) and then the plastic one for the Vol+. Weird. Once I have updated the firmware, I'll try that again. Thank you. I got the firmware report with my universal remote - not the aluminum emotiva one. Interesting. My UMC-1 is W7.04.00.07 |
|
poggy
Minor Hero
Posts: 11
|
Post by poggy on Sept 16, 2011 19:47:44 GMT -5
Hitting those 3 keys has no effect on my UMC-1. Suddenly, my UMC-1 audio goes silent when I pause or skip my DVR. This is extremely annoying. Can someone explain how to fix this problem? thanks, john This is a well known issue with the UMC-1 and virtually all DVRs. With any luck, the next firmware update (due at any time now) will fix this issue. Other than waiting, you might try avoiding an HDMI connection from your DVR and connecting it to the UMC-1 via component video (which fully supports the max resolution of hi-def via cable... 1080i) and a coax or optical digital connection for audio. Hope this helps... Thank you. I was using dvr hdmi for video and optical for audio, so I think my setup was wrong. Switching to hdmi for both did the trick. Thanks! John |
|
|
|
Post by AudioHTIT on Jul 7, 2012 16:56:12 GMT -5
I realize this is an old thread, but due to its name I looked here first.
As of this date (7/7/12) the latest UMC-1 firmware version is: 7.04.00.19
|
|
