|
|
Post by tonimanero on Feb 18, 2016 9:03:20 GMT -5
Hello Keith
My problem is, when I do all the calibration process with Dirac Live LE all things run ok but when the process is complete the program starts to download the software in the XMC-1 then the proces stops in 20 seconnds and the XMC-1 shows "downloading" permanently until I close the Dirac. If I try to save the Dirac adjustments to PC, Dirac closes suddenly and I can't save the file. I don't know if adjustments are sended right to XMC1 and I can't save the file !
I tried many times and always happens the same .
I restore my Macbook to the factory settings and install the latest version of Dirac Live LE but the problem remains.
My computer is a 2015 McBookAir and the WiFi network is very strong.
Thank you very much in advance.
Jordi
|
|
|
|
Post by 509Paul on Feb 18, 2016 11:39:40 GMT -5
I have found that saving the file right after the room measurements are completed and before you tell Dirac to create the filters gives you a fighting chance of being successful and a little less likely to crash Dirac on a Mac computer. Most the time mine was crashing when I would try to send the filters to the XMC-1 but at least I had all the room measurements saved and could start over from that point.
|
|
jenix
Minor Hero
Posts: 42
|
Post by jenix on Feb 18, 2016 11:40:30 GMT -5
Hello Keith My problem is, when I do all the calibration process with Dirac Live LE all things run ok but when the process is complete the program starts to download the software in the XCM-1 then the proces stops in 20 seconnds and the XCM-1 shows "downloading" permanently until I close the Dirac. If I try to save the Dirac adjustments to PC, Dirac closes suddenly and I can't save the file. I don't know if adjustments are sended right to XCM1 and I can't save the file ! I tried many times and always happens the same . I restore my Macbook to the factory settings and install the latest version of Dirac Live LE but the problem remains. My computer is a 2015 McBookAir and the WiFi network is very strong. Thank you very much in advance. Jordi Jordi, Had the identical situation with the MAC LE software on both a 2015 MB Pro and and Air. Keith and Nick were never able to get to the bottom of it. HOWEVER, I did find a solution that worked for me. After completing the measurements i SAVED the Project, did not select CREATE Filter. I then closed out, loaded the SAVED project just created and then CREATED the filter. For whatever reason the filter loaded into the XMC without any problem. Worked for me a couple of times so hopefully it will work for you. It was worth the effort as the system sounds GREAT! Good Luck ! Sorry 509Paul, you posted while I was typing. Glad you had the same result as me. |
|
|
|
Post by tonimanero on Feb 18, 2016 12:21:25 GMT -5
Hello, thanks for the quick response to both !!!
I'll try tonight and I will explain if it works for me.
Thank you !!
|
|
|
|
Post by wilburthegoose on Feb 18, 2016 13:47:16 GMT -5
FWIW, doing those saves is a good idea if your're on a Windows PC too. My Dirac mantra - save early, save often  |
|
|
|
Post by albertiwell on Feb 18, 2016 15:26:25 GMT -5
The same issue here, but i am more lucky than some of you guys, cos the problem disappeared. Voila.
I did nothing, but now the Dirac full, and my McBook Pro are good friends.
I put down in notes this solution of saving project, just in case.
Greeting from Spain. (Saludos Tonimanero, te he escrito también en mundodvd)
|
|
|
|
Post by tonimanero on Feb 19, 2016 8:14:25 GMT -5
It works !!!
Once the measurements completed I save the file and then the filters was created and downloaded to XMC-1 without problem.
I think the problem comes with the last firmaware for XMC-1 because before I could do it without problem.
Thank you very much
|
|
