|
|
Post by flatpicker on Jun 14, 2020 15:27:47 GMT -5
So just discovered that the left front speaker output has gone dead on one of my UMC-200's. I was setting it up in a spare room. It has not been used in awhile. Now looks like it's done. So I kinda hate to take it to the county dump, but what else to do? It's long past it's 5 year warranty... and I don't have the box anymore either. Is this how they die... :-)
|
|
|
|
Post by novisnick on Jun 14, 2020 15:38:28 GMT -5
So just discovered that the left front speaker output has gone dead on one of my UMC-200's. I was setting it up in a spare room. It has not been used in awhile. Now looks like it's done. So I kinda hate to take it to the county dump, but what else to do? It's long past it's 5 year warranty... and I don't have the box anymore either. Is this how they die... :-) For your loss |
|
|
|
Post by 405x5 on Jun 14, 2020 15:54:01 GMT -5
Just let it go  |
|
|
|
Post by flatpicker on Jun 14, 2020 17:13:33 GMT -5
Ok then.... off to the Emotiva graveyard! |
|
|
|
Post by creimes on Jun 14, 2020 17:51:34 GMT -5
So just discovered that the left front speaker output has gone dead on one of my UMC-200's. I was setting it up in a spare room. It has not been used in awhile. Now looks like it's done. So I kinda hate to take it to the county dump, but what else to do? It's long past it's 5 year warranty... and I don't have the box anymore either. Is this how they die... :-) Set it to All Stereo and use the rear outputs  |
|
|
|
Post by flatpicker on Jun 14, 2020 18:47:24 GMT -5
So just discovered that the left front speaker output has gone dead on one of my UMC-200's. I was setting it up in a spare room. It has not been used in awhile. Now looks like it's done. So I kinda hate to take it to the county dump, but what else to do? It's long past it's 5 year warranty... and I don't have the box anymore either. Is this how they die... :-) Set it to All Stereo and use the rear outputs Ah, so it would be equivalent? I'll give that a try! I assumed the rear was putting out a different spec, but I guess if it is fully stereo mode with full range, then that is a great recovery. I only need 2-channel for this setup, so that would be great to give it some more life. Thanks! |
|
|
|
Post by daveczski65 on Jun 14, 2020 19:04:43 GMT -5
Set it to All Stereo and use the rear outputs Ah, so it would be equivalent? I'll give that a try! I assumed the rear was putting out a different spec, but I guess if it is fully stereo mode with full range, then that is a great recovery. I only need 2-channel for this setup, so that would be great to give it some more life. Thanks! I use my zone 2 outputs on my UMC-1 that lost all its channels ..now just use it in stereo for the bedroom.Sucks u send all that money and after 5 plus yrs,,It is obsolete. |
|
|
|
Post by pedrocols on Jun 14, 2020 19:19:39 GMT -5
Be responsible and recycle. 😁
|
|
|
|
Post by selind40 on Jun 14, 2020 20:29:32 GMT -5
Buy the MC-700 from the lounge member that he selling......problem solved.
|
|
|
|
Post by vcautokid on Jun 14, 2020 23:43:00 GMT -5
Yep all channel stereo and you will be good unless that doesn't work then seek an alternative.
|
|
|
|
Post by creimes on Jun 15, 2020 0:59:32 GMT -5
Set it to All Stereo and use the rear outputs Ah, so it would be equivalent? I'll give that a try! I assumed the rear was putting out a different spec, but I guess if it is fully stereo mode with full range, then that is a great recovery. I only need 2-channel for this setup, so that would be great to give it some more life. Thanks! Unless all stereo means each speaker gets a Stereo signal haha, I'm not 100% positive as I don't use that setting  Chad |
|
|
|
Post by flatpicker on Jun 15, 2020 7:53:03 GMT -5
Ah, so it would be equivalent? I'll give that a try! I assumed the rear was putting out a different spec, but I guess if it is fully stereo mode with full range, then that is a great recovery. I only need 2-channel for this setup, so that would be great to give it some more life. Thanks! Unless all stereo means each speaker gets a Stereo signal haha, I'm not 100% positive as I don't use that setting Chad I first tried the rear channel/all stereo route but didn't get anything on either channel, so I turned to the zone 2 approach and it worked fine... so the umc-200 is saved from the scrap bin... thanks! |
|
|
|
Post by amped on Jun 15, 2020 15:31:40 GMT -5
Throw it away!
|
|
|
|
Post by creimes on Jun 15, 2020 16:17:22 GMT -5
Unless all stereo means each speaker gets a Stereo signal haha, I'm not 100% positive as I don't use that setting Chad I first tried the rear channel/all stereo route but didn't get anything on either channel, so I turned to the zone 2 approach and it worked fine... so the umc-200 is saved from the scrap bin... thanks! Strange that the rear outputs didn't work, unless you have them set to None in the menu ? but if Zone 2 works that's all you need. Chad |
|
|
|
Post by daveczski65 on Jun 15, 2020 19:06:54 GMT -5
You could also try and get a UMC-200 that is for parts and change out the audio board,I thought about doing that with the UMC-1,as there were a few on ebay last r that lost the video side of things.But i am happy with the zone 2
|
|
