|
|
Post by snodog on Feb 15, 2010 16:40:20 GMT -5
Hey just a couple quick questions. Ran the EmoQ and the distance was dead on, I am curious as to the 250hz for my fronts and then 200hz for my center. Is this normal for my speakers? They are Paradigm studio 40's. Is there a standard setting for this in the size and crossover setup part? I hate that my bass is so punchy in my smaller living room.
|
|
|
|
Post by snodog on Feb 15, 2010 16:48:19 GMT -5
Wow two channel stereo does sound pretty damn good
|
|
ratmice
Emo VIPs 
I'm not an actor, but I play one on TV.
Posts: 1,853
|
Post by ratmice on Feb 15, 2010 16:52:42 GMT -5
Well the studio 40s are rated to 35 hz, so something in the range of 50ish (with a 12 db slope) would prolly be good. You could just start at the typical 80 Hz for all speakers and work form there. Check your sub trim- mine is always gets set to +10dB and it sounds horrible. Start at zero and inch it up/down until it's to your liking.
|
|
|
|
Post by snodog on Feb 15, 2010 16:57:31 GMT -5
That is strange then it got the distance perfectly and way overshot the hz. I only did it once it was soooo Fu#king loud. I would rather do it manually I think.
|
|
|
|
Post by snodog on Feb 15, 2010 20:07:28 GMT -5
Cant get the SACD to work via Oppo HDMI.
|
|
|
|
Post by roadrunner on Feb 15, 2010 20:32:07 GMT -5
To get the OPPO to play nice with the UMC-1 on SACD material you need it to send LPCM over HDMI instead of DSD. Have you tried that yet? If that is what you are doing and still don't get a signal to the UMC-1 double check all your settings in both pieces. If that doesn't work, call Emotiva first thing in the morning. These will take care of you. ;D
|
|
klinemj
Emo VIPs
Official Emofest Scribe
Posts: 15,090
|
Post by klinemj on Feb 15, 2010 20:42:56 GMT -5
snodog...two questions (ok, 2 w/probes...):
1) on your x-over settings that Emo-Q reco'd for your fronts, when you look at the multi-channel EQ settings, what is the frequency at which you see a 3 dB jump vs. the next highest frequency level above that jump? (Better yet, can you share screen shots of the EQ settings for each speaker you think the x-over is set wrong?)
2) when you say "it was (explitive) loud", I presume your mean the test signals...right? Got a dB meter so you could gauge how loud it actually is? Also, it didn't shut down your amps or damage anything, did it? Just curious...
Thanks,
Mark
|
|
|
|
Post by pynchon on Feb 15, 2010 20:45:52 GMT -5
Hey just a couple quick questions. Ran the EmoQ and the distance was dead on, I am curious as to the 250hz for my fronts and then 200hz for my center. Is this normal for my speakers? They are Paradigm studio 40's. Is there a standard setting for this in the size and crossover setup part? I hate that my bass is so punchy in my smaller living room. EmoQ is probably 'technically' being accurate - I'd manually set it at 150hz for your mains |
|
|
|
Post by snodog on Feb 15, 2010 21:00:24 GMT -5
Ok I did change the Oppo to LPCM and I am not getting any sound at all on anything. I have tried a regular cd and no sound detected and now a blu ray movie. Checked all the cables again to make sure the hdmi didnt come loose.
|
|
klinemj
Emo VIPs
Official Emofest Scribe
Posts: 15,090
|
Post by klinemj on Feb 15, 2010 21:00:54 GMT -5
ps...which specific model are your fronts?
|
|
ratmice
Emo VIPs
I'm not an actor, but I play one on TV.
Posts: 1,853
|
Post by ratmice on Feb 15, 2010 21:06:39 GMT -5
^^ Studio 40s (says in post #1)
|
|
ratmice
Emo VIPs
I'm not an actor, but I play one on TV.
Posts: 1,853
|
Post by ratmice on Feb 15, 2010 21:07:31 GMT -5
Hey just a couple quick questions. Ran the EmoQ and the distance was dead on, I am curious as to the 250hz for my fronts and then 200hz for my center. Is this normal for my speakers? They are Paradigm studio 40's. Is there a standard setting for this in the size and crossover setup part? I hate that my bass is so punchy in my smaller living room. EmoQ is probably 'technically' being accurate - I'd manually set it at 150hz for your mains The speakers have a rated bass extension down to 35 Hz, why would you set them to 150? |
|
ICBM99
Emo VIPs
When will then be now? ...Soon.
Posts: 1,702
|
Post by ICBM99 on Feb 15, 2010 21:10:23 GMT -5
snodog,
Is your amp on, on that input?
By the sound of it, you're getting 2ch from the oppo (over HDMI), but not SACD? correct?
I don't have any SACD's, so I can't tell you what I've got mine set to.
|
|
|
|
Post by snodog on Feb 15, 2010 21:14:23 GMT -5
Im only getting sound from optical now for my cable. Im not getting sound at all from the oppo on any settings. Is my amp on that input? It is connected to the umc but I took the trigger cable off because it shut off earlier via the same problem darien had with both component and hdmi being hooked up caused the trigger cable not to work right....
|
|
|
|
Post by snodog on Feb 15, 2010 21:15:02 GMT -5
If I reset this *bleep* does that mean all the settings are lost too???
|
|
klinemj
Emo VIPs
Official Emofest Scribe
Posts: 15,090
|
Post by klinemj on Feb 15, 2010 21:27:33 GMT -5
That's why I asked what I did re. a screen shot of the EQ result.
Per Lonnie's video, Emo-Q is set to figure out the x-over level based on where the final output shows -3 dB.
If I understood this correctly, if the room EQ results shows the fronts not needing 3 dB (or more) boost to get to flat frequency at ~150 hz (per your results), there's an Emo-Q error.
If not, yhrn Emo-Q is correct. And, there's either a room issue OR a reproduction issue (in the source, the pre/pro, the amp, the speakers) OR a data collection error (as in, the mic). Process of elimination, that's all (sorry, 25+ year engineer typing...rather Spock-like, sorry...)
|
|
ratmice
Emo VIPs
I'm not an actor, but I play one on TV.
Posts: 1,853
|
Post by ratmice on Feb 15, 2010 21:29:04 GMT -5
If you're referring to the UMC, then yes. It shouldn't take too long to redo the inputs, though.
|
|
|
|
Post by snodog on Feb 15, 2010 21:32:50 GMT -5
No thats cool I like Spock. I just need to figure out this input thing first then ill try that
|
|
klinemj
Emo VIPs
Official Emofest Scribe
Posts: 15,090
|
Post by klinemj on Feb 15, 2010 21:45:28 GMT -5
If you should happen to get to the point you decide to reset the unit, please take a photo of your Emo-Q reco'd EQ settings and post it prior to resetting. I am really curious as to what you get.
Thanks & good luck w/the input thing... (spock here...)
|
|
|
|
Post by snodog on Feb 15, 2010 21:47:18 GMT -5
Ok so this is kind of weird but here goes, in order to regain sound from the Oppo I had to use its remote to turn up the volume from zero then the output on the Umc kicked back on. I dont know why the hell that would affect it I was looking for a way to shut off the volume entirely on the oppo so it would just be sent to processor, anyone know how to do this?
|
|
