hemster
Global Moderator 
Particle Manufacturer
...still listening... still watching
Posts: 51,951
|
Post by hemster on Feb 9, 2010 10:04:27 GMT -5
RSavage.. Yes. The update can be applied again (according to the instructions provided by Emotiva).
Still, at some future point if I want to check what the firmware version is, where can I do that? That's really something that I would love to know.
|
|
lonnie
Administrator
GM
OZ- 'Pay no attention to the man behind the curtain'
Posts: 1,292
|
Post by lonnie on Feb 9, 2010 10:05:27 GMT -5
Nothing wrong with my amp. I followed the directions and it said update was successful. Let's wait and see what others have to say before you blame me. I apologize if it came across like that, but we have spent countless hours testing and retesting the software, so I don't believe it to be screwed up. If you are running into issues, then try doing the update again and lets see if that resolves it for you. |
|
lonnie
Administrator
GM
OZ- 'Pay no attention to the man behind the curtain'
Posts: 1,292
|
Post by lonnie on Feb 9, 2010 10:08:49 GMT -5
Forgive me if this is covered elsewhere but a search found nothing. Is there a firmware version displayed (or can be displayed) somewhere so that after the upgrade, I can confirm that the update was successful? (I know that the upgrade process itself may state this but want to know if there's somewhere in the menu system where the firmware version can be displayed). Thanks. Actually yes, all you have to do is while the umc is on, press Mute, then press Status then press Volume up. The VFD on the UMC will display the current software version for about 10 seconds. It won't show this on the OSD, just on the VFD. So if in doubt, you can always check and see.  |
|
lonnie
Administrator
GM
OZ- 'Pay no attention to the man behind the curtain'
Posts: 1,292
|
Post by lonnie on Feb 9, 2010 10:09:59 GMT -5
Good question Hemster. In addition, if you suspect something went wrong with an update....can the updater be applied again? Just curious R Absolutely. Its not a problem to reflash the unit if you run into any issues. |
|
Bruce
Emo VIPs 
Posts: 844
|
Post by Bruce on Feb 9, 2010 10:21:51 GMT -5
Will this update FIX the problem with the USP-1 and the UMC-1 remote control problems?  ? |
|
|
|
Post by owtuv on Feb 9, 2010 10:24:06 GMT -5
Forgive me if this is covered elsewhere but a search found nothing. Is there a firmware version displayed (or can be displayed) somewhere so that after the upgrade, I can confirm that the update was successful? (I know that the upgrade process itself may state this but want to know if there's somewhere in the menu system where the firmware version can be displayed). Thanks. Actually yes, all you have to do is while the umc is on, press Mute, then press Status then press Volume up. The VFD on the UMC will display the current software version for about 10 seconds. It won't show this on the OSD, just on the VFD. So if in doubt, you can always check and see. Lonnie, Why not add FW Info to the OSD menu system, pretty much like Oppo does it with the BDP-83? Would make it very user friendly. Best regards, Ole Willy Tuv |
|
|
|
Post by jmilton on Feb 9, 2010 10:29:01 GMT -5
I'll update this evening. Glad my wife has a laptop...that'll make this easier. i hope the update fixes more than the few things listed. really, a faster rotary knob is the least of the issues. I have to recal. my levels every time I turn the UMC on each day. It often default to 480p. Small, but annoying issues.  The complete list of what was addressed is quite extensisve. We made a lot of behind the scene changes that will stream line a lot of the functions. Thank you all for your hard work. We moan a lot, but we really do appreciate your hard work and your corporate attitude of respect and fair play with your customer base. Your company has provided a lot of us "average Joe's" an exciting way into the hi-end market...and for that, you have or unwavering gratitude. (You can't see me, but I am giving you a standing ovation and yelling, "Speech, speech"!) |
|
|
|
Post by dropzone7 on Feb 9, 2010 10:32:58 GMT -5
I am moist with anticipation!  eeeuuuwww... Seriously, I'm excited for you too! Maybe not moist...but happy for ya! ;D |
|
|
|
Post by jimsfield on Feb 9, 2010 10:34:41 GMT -5
Dan -- forgive me but does the update also add the discrete IR codes? thanks, twj Yes, there is actually two firware updates in the software. UMC1_V102_001 is an update to the front panel micro-controller that includes the discrete IR codes. Umc1HDMI_5.46.07_100208 is the new firware for the audio and video. Lonnie, which discrete IR codes were added and how do we access those codes? I'm most interested in the ones for Inputs HDMI1 and HDMI2. The ones for resolution would also be nice. |
|
lonnie
Administrator
GM
OZ- 'Pay no attention to the man behind the curtain'
Posts: 1,292
|
Post by lonnie on Feb 9, 2010 10:37:49 GMT -5
Actually yes, all you have to do is while the umc is on, press Mute, then press Status then press Volume up. The VFD on the UMC will display the current software version for about 10 seconds. It won't show this on the OSD, just on the VFD. So if in doubt, you can always check and see. Lonnie, Why not add FW Info to the OSD menu system, pretty much like Oppo does it with the BDP-83? Would make it very user friendly. Best regards, Ole Willy Tuv The firware showing on the VFD is how we did it from the beginning and never really looked at adding more pages to the OSD but it is a good suggestion. |
|
|
|
Post by jmilton on Feb 9, 2010 10:40:03 GMT -5
...no worries. Just slightly sweaty palms. Now for a convenient excuse to go home early today. I haven't tried leprosy yet. |
|
lonnie
Administrator
GM
OZ- 'Pay no attention to the man behind the curtain'
Posts: 1,292
|
Post by lonnie on Feb 9, 2010 10:40:27 GMT -5
The complete list of what was addressed is quite extensisve. We made a lot of behind the scene changes that will stream line a lot of the functions. Thank you all for your hard work. We moan a lot, but we really do appreciate your hard work and your corporate attitude of respect and fair play with your customer base. Your company has provided a lot of us "average Joe's" an exciting way into the hi-end market...and for that, you have or unwavering gratitude. (You can't see me, but I am giving you a standing ovation and yelling, "Speech, speech"!) Standing Ovation? ?? I think I will leave that one alone, that could go down the wrong path really quick. ;D ;D |
|
lonnie
Administrator
GM
OZ- 'Pay no attention to the man behind the curtain'
Posts: 1,292
|
Post by lonnie on Feb 9, 2010 10:42:31 GMT -5
Yes, there is actually two firware updates in the software. UMC1_V102_001 is an update to the front panel micro-controller that includes the discrete IR codes. Umc1HDMI_5.46.07_100208 is the new firware for the audio and video. Lonnie, which discrete IR codes were added and how do we access those codes? I'm most interested in the ones for Inputs HDMI1 and HDMI2. The ones for resolution would also be nice. Ummmm the dog ate my home work............... Seriously, the discrete code doc is on my computer at home. I will post the hex codes tomorrow for everyone. |
|
DYohn
Emo VIPs
Posts: 18,487
|
Post by DYohn on Feb 9, 2010 11:06:01 GMT -5
Just tried emoq and it sent my amp into protect mode. This software is screwed up. EMO-Q does output a rather high level signal: what amp are you using and what is the impedance of your seakers? |
|
|
|
Post by agehring on Feb 9, 2010 11:14:16 GMT -5
I don't want to be a pain in the "*bleep*", and I don't even have my UMC-1 yet...
But, Is there any plans to support flashing the UMC-1 with something other than a MS Windows system (I don't even own one...)
P.S.: Need help with a Apple OS X driver/usb interface?
|
|
pitbullmike
Emo VIPs
C'mon ladies, play us a tasty lick!
Posts: 1,775
|
Post by pitbullmike on Feb 9, 2010 11:16:23 GMT -5
why couldn't there be an option for both basic 2ch and all channel stereo? I love listening to my music in all channel stereo mode.  When its time for me to have my UMC-1 can I perhaps get this option back |
|
|
|
Post by theoldphart on Feb 9, 2010 11:20:13 GMT -5
would love to know whether the option for all channel stereo is still there. It has been changed to two channel Never mind,Lonnie already answered |
|
ratmice
Emo VIPs
I'm not an actor, but I play one on TV.
Posts: 1,853
|
Post by ratmice on Feb 9, 2010 11:25:06 GMT -5
OK, anyone have any luck trying to install this using bootcamp on OS X? The installer just hangs for me.
|
|
RSavage
Emo VIPs
My goal is to live forever. So far, so good.
Posts: 674
|
Post by RSavage on Feb 9, 2010 11:26:04 GMT -5
why couldn't there be an option for both basic 2ch and all channel stereo? I love listening to my music in all channel stereo mode. I know you can't please everyone....but I'll put my vote in for the option to have it both ways as well. R |
|
|
|
Post by BillBauman on Feb 9, 2010 11:27:07 GMT -5
why couldn't there be an option for both basic 2ch and all channel stereo? I love listening to my music in all channel stereo mode. When its time for me to have my UMC-1 can I perhaps get this option back I would like to heavily second this. I know there is hot debate over 5-channel, and even how "best" to implement 5-channel, but it seems that having a 5-channel stereo mode is an age-old standard that many people still enjoy today. I also don't think that the standard "stereo" mode should ever be 5-channel. It seems both options should be readily available on any modern processor or AVR. |
|
?
eeeuuuwww...
